How To Fix EHPRC_CPM_CHECK126 - Calculated weight for part &1 or component &2 is missing

SAP Error Message - Details

• Message type: E = Error

• Message class: EHPRC_CPM_CHECK - Messages for Checks

• Message number: 126

• Message text: Calculated weight for part &1 or component &2 is missing

Compliance check criterion 81 is mapped to message EHPRC_CPM_CHECK126

What causes this issue?

You have executed for a specific material the compliance check for a
regulatory list. This list is configured to use substances that are
regulated at the part level and not at the homogeneous level. The weight
can also be necessary if the regulatory substance list uses
classifications, which require weight information on the part level.
The calculation of the compliance status for parts based upon the
declarable substances from the related components. The system requires a
calculated weight for the part and the component.
One of the following applies:
Measured weight for part is missing.
Weight information for bulks and basic materials in composition of part
is missing.

System Response

The compliance check was not able to calculate the weight and mass
fraction of the declarable substances from the component against the
parent part.

How to fix this error?

Check the product structure where the weights for the parent part or a
component is missing. Enter missing weight details.

Procedure for System Administrators

The system issues an error message and will not allow you to continue with this transaction until the error is resolved.

INCLUDE EHPRC_CPM_CHECK OBJECT DOKU ID TX
81.

Error message extract from SAP system. Copyright SAP SE.

Smart SAP Assistant

• What is the cause and solution for SAP error message EHPRC_CPM_CHECK126 - Calculated weight for part &1 or component &2 is missing ?

  The SAP error message EHPRC_CPM_CHECK126 indicates that the system is unable to find the calculated weight for a specific part or component in the context of the Engineering Change Management (ECM) or Product Lifecycle Management (PLM) processes. This error typically arises when the system expects a weight value for a part or component but cannot retrieve it, which can affect various processes such as costing, planning, or reporting.
  Causes:
  
  Missing Data: The weight data for the specified part or component may not have been entered or maintained in the system.
  Incorrect Configuration: The configuration settings for the material master or the relevant part/component may not be set up correctly.
  Data Inconsistency: There may be inconsistencies in the data due to incomplete updates or errors during data migration.
  Material Master Issues: The material master record for the part/component may not have the necessary weight information filled out.
  
  Solutions:
  
  
  Check Material Master: 
  
  Go to the material master record for the part or component in question (transaction code MM03).
  Verify that the weight fields (e.g., gross weight, net weight) are filled in correctly. If they are missing, update the material master with the correct weight information.
  
  
  
  Review Configuration:
  
  Ensure that the configuration settings for the relevant materials and components are correct. This may involve checking the settings in the material type or the relevant views in the material master.
  
  
  
  Data Consistency Check:
  
  Run consistency checks or reports to identify any discrepancies in the data. This may involve using transaction codes like MM02 to update or correct any inconsistencies.
  
  
  
  Consult Documentation:
  
  Review any relevant documentation or guidelines for maintaining material master data to ensure compliance with the required standards.
  
  
  
  Contact Support:
  
  If the issue persists after checking the above points, consider reaching out to your SAP support team or consulting SAP Notes for any known issues or patches related to this error message.
  
  
  
  Related Information:
  
  Transaction Codes: 
  
  MM03 - Display Material
  MM02 - Change Material
  MM01 - Create Material
  
  
  SAP Notes: Check SAP Notes for any specific fixes or updates related to this error message.
  Documentation: Review SAP Help documentation for Engineering Change Management and Product Lifecycle Management for best practices in maintaining material data.
  
  By following these steps, you should be able to resolve the error message EHPRC_CPM_CHECK126 and ensure that the calculated weight for the specified part or component is correctly maintained in the system.