How To Fix USMD2047 - Inconsistencies between UI element &2 and UI element &1

SAP Error Message - Details

• Message type: E = Error

• Message class: USMD2 - Master Data: UI Modeling

• Message number: 047

• Message text: Inconsistencies between UI element &2 and UI element &1

What causes this issue?

All attributes that are used within the same table for the lower-level
UI elements of UI elements with the type <LS>Table Column</> or
<LS>Table Column with Key Field</> must have the same higher-level
entity types. The higher-level entity types of the attributes of UI
element &V1& and UI element &V2& are different, however.

System Response

The system issues an error message and will not allow you to continue with this transaction until the error is resolved.

INCLUDE CHANGES_CANNOT_BE_SAVED OBJECT DOKU ID TX

How to fix this error?

Change the attribute of UI element &V1& or &V2& to create a table.

Procedure for System Administrators

Error message extract from SAP system. Copyright SAP SE.

Smart SAP Assistant

• What is the cause and solution for SAP error message USMD2047 - Inconsistencies between UI element &2 and UI element &1 ?

  The SAP error message USMD2047 indicates that there are inconsistencies between two UI elements in the SAP User Interface (UI) for Master Data Governance (MDG). This error typically arises when there is a mismatch in the data or configuration between the two UI elements being compared.
  Cause:
  The inconsistency can be caused by several factors, including:
  
  Data Mismatch: The data in the two UI elements may not match due to incorrect entries or updates that were not synchronized.
  Configuration Issues: There may be issues in the configuration of the UI elements, such as incorrect field mappings or settings in the MDG configuration.
  Custom Development: If there are custom enhancements or developments, they may not be properly aligned with the standard UI elements.
  Versioning Issues: If there are different versions of the data or UI elements being used, this can lead to inconsistencies.
  
  Solution:
  To resolve the USMD2047 error, you can take the following steps:
  
  
  Check Data Consistency:
  
  Review the data in both UI elements to identify any discrepancies. Ensure that the data is consistent and correctly entered.
  
  
  
  Review Configuration:
  
  Check the configuration settings for the UI elements in the MDG system. Ensure that the field mappings and settings are correctly defined and aligned.
  
  
  
  Debugging:
  
  If you have access to the development environment, you can debug the application to trace where the inconsistency is occurring. This may involve checking the underlying data models and how they are being populated in the UI.
  
  
  
  Custom Code Review:
  
  If there are any custom developments, review the code to ensure that it is not causing the inconsistency. Make sure that any custom logic aligns with the standard behavior of the UI elements.
  
  
  
  Consult Documentation:
  
  Refer to SAP documentation or notes related to the specific version of MDG you are using. There may be known issues or patches available that address this error.
  
  
  
  Testing:
  
  After making changes, conduct thorough testing to ensure that the issue is resolved and that no new issues have been introduced.
  
  
  
  Seek Support:
  
  If the issue persists, consider reaching out to SAP support or consulting with an SAP expert who specializes in MDG for further assistance.
  
  
  
  Related Information:
  
  SAP Notes: Check for any relevant SAP Notes that may provide additional insights or solutions for this specific error.
  MDG Documentation: Review the official SAP MDG documentation for best practices on UI configuration and data management.
  Community Forums: Engage with SAP community forums or user groups where similar issues may have been discussed, and solutions shared.
  
  By following these steps, you should be able to identify and resolve the inconsistencies causing the USMD2047 error in your SAP MDG environment.