How To Fix SCTS_AIM058 - No lock modes adjustment P -> X needed. No tables with lock mode P found.

SAP Error Message - Details

• Message type: E = Error

• Message class: SCTS_AIM - Messages for the AIM meta data repository

• Message number: 058

• Message text: No lock modes adjustment P -> X needed. No tables with lock mode P found.

What causes this issue?

During a ZDM upgrade, some database tables can be accessed by both the
productive application and the after-import methods (AIM) in parallel.
For these tables, it must be ensured that the productive application
does not write data into the key areas accessed (read or write access)
by the after-import method. To ensure this, the AIM author declares in
which way these key ranges are blocked in the productive application.
The most important options are the lock modes "P" = "Write access to the
relevant key ranges is blocked" and "X" = "Write access to the complete
table is blocked".
In cases where the key ranges accessed by the AIM are blocked by special
locking mechanisms (such as lock mode = "P") in the application code
(which exist from a particular application release and support package
level (R/SPL)), it may happen that the source release of the current
upgrade is lower than R/SPL. In this case, the particular locking
mechanisms are not in place. This can cause data inconsistencies after
the upgrade.
To avoid these inconsistencies, the upgrade tool sets these tables as
read-only for the productive application on database level. For example,
the upgrade tool changes the classification provided by the AIM author
from "P" to "X".
For the AIM inspected here, no re-classification is necessary since the
AIM does not access a table with lock mode "P".

System Response

The upgrade tool informs you about this fact by writing this message to
the upgrade log.

How to fix this error?

No action required.

Procedure for System Administrators

The system issues an error message and will not allow you to continue with this transaction until the error is resolved.

Error message extract from SAP system. Copyright SAP SE.

Smart SAP Assistant

• What is the cause and solution for SAP error message SCTS_AIM058 - No lock modes adjustment P -> X needed. No tables with lock mode P found. ?

  The SAP error message SCTS_AIM058 indicates that there is no need for a lock mode adjustment from "P" (for "Protected") to "X" (for "Exclusive") because the system did not find any tables that are currently locked with mode "P". This message is typically related to the SAP Change and Transport System (CTS) and can occur during transport requests or when performing certain operations that involve locking mechanisms.
  Cause:
  
  No Tables Locked in Mode P: The primary cause of this error is that there are no database tables currently locked in mode "P". This means that the system is trying to adjust lock modes, but there are no relevant locks to adjust.
  Transport Request Status: The transport request may not be in a state that requires a lock adjustment.
  System Configuration: There may be configuration settings or conditions in the system that prevent any tables from being locked in mode "P".
  
  Solution:
  
  Check Lock Status: Use transaction code SM12 to check the current lock entries in the system. Look for any entries that are locked in mode "P". If there are none, this message is expected and can be ignored.
  Review Transport Request: Ensure that the transport request you are working with is correctly configured and is in the appropriate status for processing.
  System Logs: Check the system logs for any additional messages or errors that might provide more context about the situation.
  Re-run the Process: If you believe there should be tables locked in mode "P", try re-running the process that triggered the error to see if it was a transient issue.
  Consult Documentation: Review SAP documentation or notes related to the Change and Transport System for any specific guidance on this error message.
  
  Related Information:
  
  Transaction Codes: Familiarize yourself with relevant transaction codes such as SE09 (Transport Organizer), SE10 (Transport Organizer for Administrators), and SM12 (Display and Delete Locks).
  SAP Notes: Check SAP Notes for any known issues or patches related to this error message. You can search for the error message or related keywords in the SAP Support Portal.
  SAP Community: Engage with the SAP Community forums to see if other users have encountered this error and what solutions they have found.
  
  In summary, the error message SCTS_AIM058 is generally informational and indicates that there are no tables locked in mode "P" that require adjustment. If you are not experiencing any functional issues, it may not require any action. However, if you are facing issues, following the steps above should help you diagnose and resolve the situation.