How To Fix /SAPAPO/OM_ERROR179 - Invalid max_tolerance for pegging area

SAP Error Message - Details

• Message type: E = Error

• Message class: /SAPAPO/OM_ERROR -

• Message number: 179

• Message text: Invalid max_tolerance for pegging area

Self-Explanatory Message

Since SAP believes that this specific error message is 'self-explanatory,' no more information has been given.The majority of messages in the SAP system have a message text, however this is frequently insufficient to comprehend or resolve the problem.

To make things easier, more detailed information is frequently added to describe the issue, how to fix it, and the necessary steps or configuration modifications.

Unfortunately, there isn't any extra information in this error notice.

What else can you do?

First, use our AnswerBot below to get a possible cause and solution (requires a premium subscription).

Also, review the in-depth Common Questions & Answers listed below; you could discover a solution there or be able to connect with others who have faced similar challenges.

You can also try searching the SAP support portal (support.sap.com) but you need a special user ID to access it. It is possible that an SAP support note exists that provides additional details about the mistake or even steps for fixing it.

Smart SAP Assistant

• What is the cause and solution for SAP error message /SAPAPO/OM_ERROR179 - Invalid max_tolerance for pegging area ?

  The SAP error message /SAPAPO/OM_ERROR179 Invalid max_tolerance for pegging area typically occurs in the context of Advanced Planning and Optimization (APO) within SAP. This error is related to the configuration of pegging areas and the tolerance settings for them.
  Cause:
  
  
  Invalid Tolerance Settings: The error usually arises when the maximum tolerance value set for a pegging area is invalid. This could be due to:
  
  The maximum tolerance value being set to a negative number.
  The maximum tolerance exceeding the allowable limits defined in the system.
  Incorrect configuration of the pegging area in the APO system.
  
  
  
  Data Inconsistencies: There may be inconsistencies in the data related to the pegging area, such as missing or incorrect entries in the configuration tables.
  
  
  Custom Code or Enhancements: If there are custom developments or enhancements in the APO system, they might inadvertently lead to this error if they manipulate the pegging area settings.
  
  
  Solution:
  
  
  Check Tolerance Settings:
  
  Navigate to the configuration settings for the pegging area in the APO system.
  Verify the maximum tolerance values set for the pegging area. Ensure that they are within valid ranges (typically non-negative and within system-defined limits).
  
  
  
  Adjust Configuration:
  
  If the maximum tolerance is set incorrectly, adjust it to a valid value.
  Ensure that all related settings for the pegging area are correctly configured.
  
  
  
  Data Consistency Check:
  
  Run consistency checks on the data related to the pegging area to identify any discrepancies.
  Correct any inconsistencies found in the configuration tables.
  
  
  
  Review Custom Code:
  
  If there are any custom developments affecting the pegging area, review the code to ensure it does not introduce invalid values for the maximum tolerance.
  
  
  
  Consult Documentation:
  
  Refer to SAP documentation or notes related to the specific version of APO you are using for any known issues or additional configuration guidelines.
  
  
  
  SAP Support:
  
  If the issue persists after checking the above points, consider reaching out to SAP support for further assistance. They may provide patches or additional insights based on the specific version and configuration of your system.
  
  
  
  Related Information:
  
  Transaction Codes: You may need to use transaction codes like /SAPAPO/OM to access the relevant configuration settings.
  SAP Notes: Check for any relevant SAP Notes that might address this specific error or provide guidance on configuration best practices.
  Documentation: Review the SAP Help Portal for detailed documentation on configuring pegging areas and tolerance settings in APO.
  
  By following these steps, you should be able to identify and resolve the cause of the /SAPAPO/OM_ERROR179 error in your SAP APO system.