How To Fix /SAPAPO/CFM_MSG303 - Different number of buckets for key figs - loc. &1 prd. &2 key fig. c. &3

SAP Error Message - Details

• Message type: E = Error

• Message class: /SAPAPO/CFM_MSG -

• Message number: 303

• Message text: Different number of buckets for key figs - loc. &1 prd. &2 key fig. c. &3

Self-Explanatory Message

Since SAP believes that this specific error message is 'self-explanatory,' no more information has been given.The majority of messages in the SAP system have a message text, however this is frequently insufficient to comprehend or resolve the problem.

To make things easier, more detailed information is frequently added to describe the issue, how to fix it, and the necessary steps or configuration modifications.

Unfortunately, there isn't any extra information in this error notice.

What else can you do?

First, use our AnswerBot below to get a possible cause and solution (requires a premium subscription).

Also, review the in-depth Common Questions & Answers listed below; you could discover a solution there or be able to connect with others who have faced similar challenges.

You can also try searching the SAP support portal (support.sap.com) but you need a special user ID to access it. It is possible that an SAP support note exists that provides additional details about the mistake or even steps for fixing it.

Smart SAP Assistant

• What is the cause and solution for SAP error message /SAPAPO/CFM_MSG303 - Different number of buckets for key figs - loc. &1 prd. &2 key fig. c. &3 ?

  The SAP error message /SAPAPO/CFM_MSG303 indicates that there is a mismatch in the number of buckets for the key figures associated with a specific location and product in the SAP Advanced Planning and Optimization (APO) module. This error typically arises during planning activities, such as when trying to execute a planning run or when performing data consistency checks.
  Cause:
  The error is caused by a discrepancy in the configuration of key figures for the specified location and product. Specifically, it occurs when the number of time buckets (periods) defined for a key figure does not match the expected number of buckets for the planning object structure. This can happen due to:
  
  Inconsistent Configuration: The key figure settings for the location and product may have been changed, leading to a mismatch.
  Data Load Issues: If data was loaded into the system without proper alignment of time buckets, it can lead to inconsistencies.
  Planning Version Differences: Different planning versions may have different configurations for key figures, leading to mismatches when trying to access or compare data across versions.
  
  Solution:
  To resolve this error, you can take the following steps:
  
  
  Check Key Figure Configuration:
  
  Go to the key figure configuration in the APO system and verify that the number of buckets for the key figures in question is consistent across all relevant planning areas and versions.
  
  
  
  Review Planning Object Structure:
  
  Ensure that the planning object structure (POS) used for the location and product is correctly defined and that it matches the key figure settings.
  
  
  
  Data Consistency Check:
  
  Perform a consistency check on the data for the affected location and product. This can often be done using transaction codes like /SAPAPO/CFM or /SAPAPO/SDP94 to analyze the planning data.
  
  
  
  Reprocess Data:
  
  If the issue arose due to data loading, consider reprocessing the data load to ensure that it aligns with the current configuration.
  
  
  
  Consult Documentation:
  
  Review SAP documentation or notes related to this error message for any specific recommendations or patches that may address the issue.
  
  
  
  Contact SAP Support:
  
  If the issue persists after checking the above points, consider reaching out to SAP support for further assistance, especially if this is a production environment.
  
  
  
  Related Information:
  
  Transaction Codes: Familiarize yourself with relevant transaction codes such as /SAPAPO/CFM for configuration management and /SAPAPO/SDP94 for planning data analysis.
  SAP Notes: Search for SAP Notes related to this error message for any known issues or fixes.
  Documentation: Review the SAP APO documentation for best practices in key figure configuration and planning object structure management.
  
  By following these steps, you should be able to identify and resolve the cause of the error message /SAPAPO/CFM_MSG303.