How To Fix RSCRT343 - Could not start RDA upload. DTP must be executed in standard mode first.

SAP Error Message - Details

• Message type: E = Error

• Message class: RSCRT - Near-To-Real-Time Messages

• Message number: 343

• Message text: Could not start RDA upload. DTP must be executed in standard mode first.

What causes this issue?

You are trying to start real-time data acquisition (RDA) for DTP &V1&,
but source &V2& requires execution of the DTP in standard mode first.
This might be due to the delta process not being initialized yet.

System Response

The RDA upload has not been started. No request has been created for DTP
&V1&.

How to fix this error?

Schedule the RDA repair process chain to execute DTP &V1& in standard
mode. When the process chain run has completed successfully, start the
RDA upload again.

Procedure for System Administrators

The system issues an error message and will not allow you to continue with this transaction until the error is resolved.

Error message extract from SAP system. Copyright SAP SE.

Smart SAP Assistant

• What is the cause and solution for SAP error message RSCRT343 - Could not start RDA upload. DTP must be executed in standard mode first. ?

  The SAP error message RSCRT343 indicates that there is an issue with the Data Transfer Process (DTP) when trying to start a Remote Data Access (RDA) upload. The message specifically states that the DTP must be executed in standard mode first before you can proceed with the RDA upload.
  Cause:
  The error typically occurs due to the following reasons:
  
  DTP Configuration: The DTP is not properly configured to allow RDA uploads. It may require an initial execution in standard mode to establish the necessary data flow and settings.
  Execution Mode: The DTP has not been executed in standard mode, which is a prerequisite for RDA uploads. The system needs to ensure that the data flow is correctly set up before allowing RDA operations.
  Data Source Issues: There may be issues with the data source or the extraction process that need to be resolved before RDA can be initiated.
  
  Solution:
  To resolve the RSCRT343 error, follow these steps:
  
  
  Execute DTP in Standard Mode:
  
  Go to the Data Warehousing Workbench (transaction code: RSA1).
  Navigate to the DTP that is causing the issue.
  Execute the DTP in standard mode. This can usually be done by selecting the DTP and choosing the "Execute" option.
  Monitor the execution to ensure it completes successfully.
  
  
  
  Check DTP Settings:
  
  Review the DTP settings to ensure that they are correctly configured for RDA. This includes checking the source and target settings, as well as any transformation rules.
  Ensure that the DTP is set up to allow RDA uploads if that is a requirement.
  
  
  
  Review Data Source:
  
  Check the data source associated with the DTP for any issues. Ensure that it is active and that there are no errors in the extraction process.
  If necessary, perform a test extraction to verify that data can be pulled from the source without issues.
  
  
  
  Consult Logs:
  
  If the DTP execution fails, check the logs for any additional error messages or warnings that could provide more context on the issue.
  
  
  
  Documentation and Support:
  
  Refer to SAP documentation for any specific requirements or configurations related to RDA and DTPs.
  If the issue persists, consider reaching out to SAP support for further assistance.
  
  
  
  Related Information:
  
  DTP (Data Transfer Process): A DTP is used in SAP BW to transfer data from a source (like an InfoSource) to a target (like an InfoProvider).
  RDA (Remote Data Access): RDA allows for the extraction of data from remote sources, which can be useful for real-time data processing.
  Standard Mode vs. RDA Mode: Standard mode is the typical execution mode for DTPs, while RDA mode is used for specific scenarios where data needs to be accessed remotely.
  
  By following these steps, you should be able to resolve the RSCRT343 error and successfully execute the DTP for RDA uploads.