How To Fix QT006 - No selected set exists for the inspection point &1 or plant &2

SAP Error Message - Details

• Message type: E = Error

• Message class: QT - QM: Inspection during production (with inspection points)

• Message number: 006

• Message text: No selected set exists for the inspection point &1 or plant &2

What causes this issue?

An inspection point (wire basket, equipment, sample, etc.) is
valuated after all characteristics have been closed. You can store a
proposal in Customizing for this purpose in two places:

The system issues an error message and will not allow you to continue with this transaction until the error is resolved.

At the inspection point level
At the plant level
If a proposal for an acceptance or rejection is stored at the inspection
point level, the system uses this proposal. Otherwise, the system uses
the selected set in the table for QM plant settings.
In this particular case, a proposal is neither available for the
inspection point (&V1&) nor the plant (&V2&).

System Response

How to fix this error?

Maintain the selected set for the <DS:SIMG.OLQW_OQE6>inspection point</>
or <DS:SIMG.SIMG_CFMENUOLQSOQS1>plant settings</>.

Error message extract from SAP system. Copyright SAP SE.

Smart SAP Assistant

• What is the cause and solution for SAP error message QT006 - No selected set exists for the inspection point &1 or plant &2 ?

  The SAP error message QT006 indicates that there is no selected set available for the specified inspection point and plant. This error typically occurs in the context of Quality Management (QM) when trying to perform quality inspections or evaluations.
  Cause:
  
  Missing Selected Set: The most common cause of this error is that there is no selected set defined for the specified inspection point in the system. A selected set is a grouping of inspection characteristics that are used during the inspection process.
  Incorrect Configuration: The inspection point or plant may not be properly configured in the system, leading to the absence of a selected set.
  Data Inconsistency: There may be inconsistencies in the master data or configuration settings related to the inspection point or the material being inspected.
  
  Solution:
  
  
  Check Selected Set Configuration:
  
  Go to the transaction code QG01 (Create Selected Set) or QG02 (Change Selected Set) in SAP.
  Verify if a selected set exists for the specified inspection point and plant. If it does not exist, you will need to create one.
  Ensure that the selected set is correctly assigned to the relevant inspection point.
  
  
  
  Review Inspection Point Settings:
  
  Use transaction code QP01 (Create Inspection Point) or QP02 (Change Inspection Point) to check the settings for the inspection point.
  Ensure that the inspection point is correctly linked to the material and plant.
  
  
  
  Check Material Master Data:
  
  Ensure that the material master data is correctly maintained, especially the Quality Management views.
  Use transaction code MM03 to view the material master and check the QM data.
  
  
  
  Consult Documentation:
  
  Review SAP documentation or help files related to Quality Management and selected sets for further guidance on configuration.
  
  
  
  Contact SAP Support:
  
  If the issue persists after checking the above configurations, consider reaching out to SAP support for assistance, as there may be specific issues related to your system setup.
  
  
  
  Related Information:
  
  
  Transaction Codes:
  
  QG01 - Create Selected Set
  QG02 - Change Selected Set
  QP01 - Create Inspection Point
  QP02 - Change Inspection Point
  MM03 - Display Material Master
  
  
  
  Quality Management (QM) Module: Understanding the QM module in SAP can help in troubleshooting and configuring inspection points and selected sets effectively.
  
  
  SAP Notes: Check for any relevant SAP Notes that may address this specific error or provide additional troubleshooting steps.
  
  
  By following these steps, you should be able to resolve the QT006 error and ensure that the selected set is properly configured for your inspection points.