How To Fix OIUBL108 - Error; no standard UoM found for UoM Group &, Dim ID &, Meas Grp &, PBA &

SAP Error Message - Details

• Message type: E = Error

• Message class: OIUBL - PRA Balancing Messages

• Message number: 108

• Message text: Error; no standard UoM found for UoM Group &, Dim ID &, Meas Grp &, PBA &

What causes this issue?

A standard Unit of Measure (UOM) was not found for the Unit of Measure
Group/Dimension combination.

System Response

PBA cannot be processed.,,,,

How to fix this error?

UOMs are attached to Unit of Measure Groups in the IMG Global Settings
for IS Oil & Gas (PRA).
,,Check to make sure a standard UOM exists for VOLUME/ENERGY in the
Unit of Measure Group.
Unit of Measure Groups are attached to PBAs via the Measurement Groups.
,,Check that the Measurement Group attached to the PBA (in the PBA
setup within CA Balancing), contains the appropriate UOM Groups for the
PBA.

Procedure for System Administrators

The system issues an error message and will not allow you to continue with this transaction until the error is resolved.

Error message extract from SAP system. Copyright SAP SE.

Smart SAP Assistant

• What is the cause and solution for SAP error message OIUBL108 - Error; no standard UoM found for UoM Group &, Dim ID &, Meas Grp &, PBA & ?

  The SAP error message OIUBL108 indicates that there is no standard Unit of Measure (UoM) found for a specified UoM Group, Dimension ID, Measurement Group, and Product Base Area (PBA). This error typically arises in the context of SAP's Oil and Gas or similar industry modules where UoM management is critical.
  Cause:
  
  
  Missing Standard UoM: The primary cause of this error is that the system cannot find a standard UoM defined for the specified UoM Group. This could be due to:
  
  The UoM Group not being properly configured.
  The standard UoM not being assigned to the UoM Group in the configuration settings.
  Incorrect or incomplete data entry in the relevant master data records.
  
  
  
  Configuration Issues: There may be issues in the configuration of the measurement groups or the product base area that do not align with the expected UoM settings.
  
  
  Data Inconsistencies: There could be inconsistencies in the data related to the UoM, such as missing entries in the relevant tables or incorrect relationships between UoM Groups and their standard UoMs.
  
  
  Solution:
  
  
  Check UoM Configuration:
  
  Navigate to the UoM configuration settings in SAP (Transaction Code: OIUUOM).
  Verify that the UoM Group in question has a standard UoM assigned to it.
  If not, assign a standard UoM to the UoM Group.
  
  
  
  Review Master Data:
  
  Check the master data for the relevant entities (e.g., products, measurement groups) to ensure that all necessary fields are filled out correctly.
  Ensure that the Dimension ID and Measurement Group are correctly defined and linked to the appropriate UoM Group.
  
  
  
  Data Consistency Checks:
  
  Run consistency checks on the UoM data to identify any discrepancies or missing entries.
  Use transaction codes like OIU_MAINTAIN or OIU_MAINTAIN_UOM to review and maintain UoM settings.
  
  
  
  Consult Documentation:
  
  Refer to SAP documentation or help resources for specific guidance on UoM configuration in your version of SAP.
  
  
  
  Engage with SAP Support:
  
  If the issue persists after checking the configuration and master data, consider reaching out to SAP support for further assistance.
  
  
  
  Related Information:
  
  UoM Groups: These are collections of units that can be used interchangeably within a specific context (e.g., volume, weight).
  Standard UoM: This is the primary unit of measure that is used for transactions and reporting.
  Measurement Groups: These are used to categorize different types of measurements (e.g., volume, pressure) in the system.
  Product Base Area (PBA): This refers to the specific area or context in which the product is measured or utilized.
  
  By following these steps, you should be able to resolve the OIUBL108 error and ensure that your UoM configurations are correctly set up in SAP.