How To Fix FDT_SERVICE358 - Division of quantities with dimensions ('&1' and '&2') is '&3', not '&4'

SAP Error Message - Details

• Message type: E = Error

• Message class: FDT_SERVICE - Formula & Derivation Tool: Services

• Message number: 358

• Message text: Division of quantities with dimensions ('&1' and '&2') is '&3', not '&4'

Self-Explanatory Message

Since SAP believes that this specific error message is 'self-explanatory,' no more information has been given.The majority of messages in the SAP system have a message text, however this is frequently insufficient to comprehend or resolve the problem.

To make things easier, more detailed information is frequently added to describe the issue, how to fix it, and the necessary steps or configuration modifications.

Unfortunately, there isn't any extra information in this error notice.

What else can you do?

First, use our AnswerBot below to get a possible cause and solution (requires a premium subscription).

Also, review the in-depth Common Questions & Answers listed below; you could discover a solution there or be able to connect with others who have faced similar challenges.

You can also try searching the SAP support portal (support.sap.com) but you need a special user ID to access it. It is possible that an SAP support note exists that provides additional details about the mistake or even steps for fixing it.

Smart SAP Assistant

• What is the cause and solution for SAP error message FDT_SERVICE358 - Division of quantities with dimensions ('&1' and '&2') is '&3', not '&4' ?

  The SAP error message FDT_SERVICE358 typically occurs in the context of financial document processing, particularly when dealing with quantities that have associated dimensions (like units of measure, currencies, etc.). This error indicates a mismatch in the expected division of quantities based on their dimensions.
  Cause:
  The error message is triggered when there is an inconsistency in the division of quantities with different dimensions. Specifically, it suggests that the system expected a certain result from the division of two quantities (with dimensions '&1' and '&2'), but the actual result was different from what was anticipated ('&3' instead of '&4').
  This can happen due to several reasons:
  
  Incorrect Configuration: The system may not be configured correctly to handle the specific dimensions involved in the transaction.
  Data Entry Errors: There may be mistakes in the data entry where quantities or dimensions are incorrectly specified.
  Incompatible Units: The units of measure or dimensions being used may not be compatible for the operation being performed.
  Custom Logic: If there are custom enhancements or logic in place, they may not be handling the division correctly.
  
  Solution:
  To resolve this error, you can take the following steps:
  
  
  Check Configuration: Review the configuration settings related to the dimensions and units of measure in the relevant SAP modules (like MM, SD, or FI). Ensure that they are set up correctly.
  
  
  Validate Data Entry: Go through the transaction data to ensure that all quantities and their respective dimensions are entered correctly. Look for any discrepancies in the units of measure.
  
  
  Review Custom Logic: If there are any custom developments or enhancements, review the code to ensure that it correctly handles the division of quantities with different dimensions.
  
  
  Test with Different Data: If possible, try to replicate the issue with different sets of data to see if the problem persists. This can help isolate whether the issue is data-specific or systemic.
  
  
  Consult Documentation: Refer to SAP documentation or notes related to this error message for any specific guidance or known issues.
  
  
  Contact SAP Support: If the issue persists after checking the above points, consider reaching out to SAP support for further assistance. Provide them with detailed information about the error, including the context in which it occurs.
  
  
  Related Information:
  
  SAP Notes: Check for any SAP Notes related to FDT_SERVICE358 for additional insights or patches that may address the issue.
  Transaction Codes: Familiarize yourself with relevant transaction codes that may help in troubleshooting, such as SE80 (Object Navigator) or SE37 (Function Module).
  Community Forums: Engage with SAP community forums or user groups where similar issues may have been discussed.
  
  By following these steps, you should be able to identify the root cause of the error and implement a suitable solution.