Stop googling SAP errors. Use our Free Essentials plan instead - no credit card needed. Start Now

Close

How To Fix W#443 - Error converting to base unit of measure for units &1 and &2


SAP Error Message - Details

  • Message type: E = Error

  • Message class: W# -

  • Message number: 443

  • Message text: Error converting to base unit of measure for units &1 and &2

  • Show details Hide details


  • Self-Explanatory Message

    Since SAP believes that this specific error message is 'self-explanatory,' no more information has been given.The majority of messages in the SAP system have a message text, however this is frequently insufficient to comprehend or resolve the problem.

    To make things easier, more detailed information is frequently added to describe the issue, how to fix it, and the necessary steps or configuration modifications.

    Unfortunately, there isn't any extra information in this error notice.



    What else can you do?

    First, use our AnswerBot below to get a possible cause and solution (requires a premium subscription).

    Also, review the in-depth Common Questions & Answers listed below; you could discover a solution there or be able to connect with others who have faced similar challenges.

    You can also try searching the SAP support portal (support.sap.com) but you need a special user ID to access it. It is possible that an SAP support note exists that provides additional details about the mistake or even steps for fixing it.


Smart SAP Assistant

  • What is the cause and solution for SAP error message W#443 - Error converting to base unit of measure for units &1 and &2 ?

    The SAP error message W#443, which states "Error converting to base unit of measure for units &1 and &2," typically occurs when there is an issue with the conversion of units of measure in the system. This error can arise in various contexts, such as during material movements, inventory management, or when processing transactions that involve different units of measure.

    Cause:

    1. Unit of Measure Configuration: The error often indicates that there is a problem with the configuration of the units of measure in the system. This could be due to:

      • Missing or incorrect conversion factors between the units of measure.
      • The base unit of measure not being defined properly for the material.
      • The units of measure being incompatible or not recognized by the system.
    2. Material Master Data: If the material master data is not set up correctly, it can lead to this error. This includes:

      • Incorrect settings in the material master regarding units of measure.
      • Missing entries in the unit of measure table.
    3. Transaction Context: The error may also occur in specific transactions where the system attempts to convert quantities from one unit of measure to another, and the conversion cannot be performed due to the reasons mentioned above.

    Solution:

    1. Check Material Master Data:

      • Go to the material master (transaction code MM03) and check the units of measure section.
      • Ensure that the base unit of measure is defined and that all necessary alternative units of measure are correctly configured with appropriate conversion factors.
    2. Review Unit of Measure Settings:

      • Use transaction code CUNI to access the unit of measure settings.
      • Verify that the conversion factors between the units of measure are correctly defined and that there are no missing entries.
    3. Check for Incompatibilities:

      • Ensure that the units of measure being used in the transaction are compatible with each other and that the system recognizes them.
    4. Test Transactions:

      • After making any changes, test the transaction again to see if the error persists.
    5. Consult Documentation:

      • Refer to SAP documentation or help resources for specific details on unit of measure configuration and troubleshooting.
    6. Contact SAP Support:

      • If the issue cannot be resolved through the above steps, consider reaching out to SAP support for further assistance.

    Related Information:

    • Unit of Measure Tables: Familiarize yourself with relevant tables such as T006 (Units of Measure) and T006A (Units of Measure for Alternative Units).
    • Transaction Codes: Common transaction codes related to material management and unit of measure include MM01 (Create Material), MM02 (Change Material), and MM03 (Display Material).
    • SAP Notes: Check for any SAP Notes related to unit of measure issues, as they may provide specific fixes or patches for known problems.

    By following these steps, you should be able to identify and resolve the cause of the W#443 error in SAP.

    • Do you have any question about this error?


      Upgrade now to chat with this error.


Instant HelpGet instant SAP help. Sign up for our Free Essentials Plan.


Related SAP Error Messages

Click the links below to see the following related messages:

Click on this link to search all SAP messages.


Rating
The AI Support Assistant is great. It provides comprehensive assistance even on the most difficult issues. I highly recommend this service.
Rate 1
John Jordan
SAP Consultant & Author