Do you have any question about this error?
Stop googling SAP errors. Use our Free Essentials plan instead - no credit card needed. Start Now →
Message type: E = Error
Message class: UC0 - General Messages for SAP Consolidation
Message number: 120
Message text: Cannot convert default value: SID does not yet exist
During the conversion of SEM-BCS default values, a default value for
value &V3& of the higher-level characteristic of characteristic &V2& was
found in client &V1&. But no SID exists for this value in the system,
that is, this value was not yet created in this system. So this value
was not yet used in this system.
This default value is not converted.
If you have not used this default value yet and do not intend to use it,
you can ignore this error message.
Otherwise proceed as follows:
Start the Consolidation Workbench after the upgrade and check the values
of characteristic &V2&. If necessary, create the master data for the
default value for value &V3& of the higher-level characteristic.
Start the XPRA for SEM-BCS again.
The system issues an error message and will not allow you to continue with this transaction until the error is resolved.
Error message extract from SAP system. Copyright SAP SE.
UC0120
- Cannot convert default value: SID does not yet exist ?The SAP error message UC0120, which states "Cannot convert default value: SID does not yet exist," typically occurs in the context of SAP systems when there is an issue related to the System ID (SID) during a conversion or migration process. This error can arise in various scenarios, such as during system upgrades, data migrations, or when configuring new systems.
Cause:
- Missing SID: The error indicates that the system is trying to reference a System ID (SID) that has not been created or is not recognized in the current context.
- Configuration Issues: There may be misconfigurations in the system settings or parameters that prevent the SID from being recognized.
- Database Issues: If the database is not properly set up or if there are issues with the database connection, the SID may not be accessible.
- Transport Issues: If you are trying to transport objects or configurations that reference a SID that does not exist in the target system, this error can occur.
Solution:
- Check SID Configuration: Ensure that the SID is correctly configured in the system. You can check the instance profile and the system parameters to verify that the SID is set up properly.
- Create the SID: If the SID does not exist, you may need to create it. This can involve setting up a new client or instance in the SAP system.
- Review Migration Steps: If this error occurs during a migration or upgrade, review the steps you have taken to ensure that all necessary components and configurations are in place.
- Database Connection: Verify that the database is running and that the connection settings are correct. Ensure that the database user has the necessary permissions.
- Transport Directory: If the error is related to transport requests, check the transport directory to ensure that all necessary objects are included and that the SID is correctly referenced.
- SAP Notes: Check the SAP Support Portal for any relevant SAP Notes that may address this specific error. There may be patches or updates that resolve the issue.
Related Information:
If the issue persists after trying the above solutions, consider reaching out to SAP support for further assistance.
Get instant SAP help. Sign up for our Free Essentials Plan.
UC0119
Invalid default values will not be converted
What causes this issue? During the conversion of SEM-BCS default values, default values for characteristic &V2& were found in client &V1&...
UC0118
SID table &3 for characteristic &2 in client &1 is invalid
What causes this issue? During the conversion of SEM-BCS default values, default values for characteristic &V2& were found in client &V1&...
UC0121
Cannot convert default value: SID does not yet exist
What causes this issue? During the conversion of SEM-BCS default values, default value &V3& of characteristic &V2& were found in clie...
UC0122
Invalid type of default value &2 for characteristic &1
What causes this issue? During the conversion of default values in client &V1&, a default value was found for characteristic &V2& wit...
Click on this link to search all SAP messages.