How To Fix /SCWM/LT015 - Start numbering with 1

SAP Error Message - Details

• Message type: E = Error

• Message class: /SCWM/LT -

• Message number: 015

• Message text: Start numbering with 1

Self-Explanatory Message

Since SAP believes that this specific error message is 'self-explanatory,' no more information has been given.The majority of messages in the SAP system have a message text, however this is frequently insufficient to comprehend or resolve the problem.

To make things easier, more detailed information is frequently added to describe the issue, how to fix it, and the necessary steps or configuration modifications.

Unfortunately, there isn't any extra information in this error notice.

What else can you do?

First, use our AnswerBot below to get a possible cause and solution (requires a premium subscription).

Also, review the in-depth Common Questions & Answers listed below; you could discover a solution there or be able to connect with others who have faced similar challenges.

You can also try searching the SAP support portal (support.sap.com) but you need a special user ID to access it. It is possible that an SAP support note exists that provides additional details about the mistake or even steps for fixing it.

Smart SAP Assistant

• What is the cause and solution for SAP error message /SCWM/LT015 - Start numbering with 1 ?

  The SAP error message /SCWM/LT015 Start numbering with 1 typically occurs in the context of the SAP Extended Warehouse Management (EWM) module. This error message indicates that there is an issue with the numbering of a certain object, such as a document or a transaction, where the numbering sequence is expected to start from 1 but does not.
  Cause:
  
  Incorrect Numbering Configuration: The numbering configuration for the relevant document type or transaction may not be set up correctly, leading to a sequence that does not start from 1.
  Custom Development: If there are custom developments or enhancements in the system, they might be affecting the numbering sequence.
  Data Migration Issues: If data has been migrated from another system, the numbering sequence may not have been properly aligned.
  User Input Error: Users may have inadvertently entered a starting number that is not 1.
  
  Solution:
  
  
  Check Numbering Configuration:
  
  Go to the configuration settings for the relevant document type in EWM.
  Ensure that the numbering is set to start from 1. This can usually be found in the customizing settings under the relevant application area.
  
  
  
  Review Custom Code:
  
  If there are any custom developments, review the code to ensure that it adheres to the expected numbering sequence.
  Make necessary adjustments to ensure that the numbering starts from 1.
  
  
  
  Data Consistency Check:
  
  Perform a consistency check on the data to ensure that there are no gaps or incorrect entries in the numbering sequence.
  If necessary, correct any discrepancies found.
  
  
  
  User Training:
  
  If the issue is due to user input, provide training to users on the correct procedures for entering data to avoid similar issues in the future.
  
  
  
  Consult SAP Notes:
  
  Check the SAP Support Portal for any relevant SAP Notes that may address this specific error message or provide additional guidance.
  
  
  
  Contact SAP Support:
  
  If the issue persists after checking the above points, consider reaching out to SAP Support for further assistance.
  
  
  
  Related Information:
  
  Transaction Codes: Familiarize yourself with relevant transaction codes in EWM that may help in troubleshooting, such as /SCWM/PRDI for inbound deliveries or /SCWM/PRDO for outbound deliveries.
  Documentation: Review SAP documentation related to EWM configuration and numbering settings for more detailed guidance.
  Community Forums: Engage with SAP community forums or user groups where similar issues may have been discussed, and solutions shared.
  
  By following these steps, you should be able to resolve the /SCWM/LT015 Start numbering with 1 error and ensure that your numbering sequences are correctly configured in SAP EWM.