How To Fix /SAPAPO/SNP_CCMS060 - Number of missing SNP time series anchors is too high

SAP Error Message - Details

• Message type: E = Error

• Message class: /SAPAPO/SNP_CCMS -

• Message number: 060

• Message text: Number of missing SNP time series anchors is too high

Self-Explanatory Message

Since SAP believes that this specific error message is 'self-explanatory,' no more information has been given.The majority of messages in the SAP system have a message text, however this is frequently insufficient to comprehend or resolve the problem.

To make things easier, more detailed information is frequently added to describe the issue, how to fix it, and the necessary steps or configuration modifications.

Unfortunately, there isn't any extra information in this error notice.

What else can you do?

First, use our AnswerBot below to get a possible cause and solution (requires a premium subscription).

Also, review the in-depth Common Questions & Answers listed below; you could discover a solution there or be able to connect with others who have faced similar challenges.

You can also try searching the SAP support portal (support.sap.com) but you need a special user ID to access it. It is possible that an SAP support note exists that provides additional details about the mistake or even steps for fixing it.

Smart SAP Assistant

• What is the cause and solution for SAP error message /SAPAPO/SNP_CCMS060 - Number of missing SNP time series anchors is too high ?

  The SAP error message /SAPAPO/SNP_CCMS060 indicates that there is a high number of missing SNP (Supply Network Planning) time series anchors in your SAP APO (Advanced Planning and Optimization) system. This can lead to issues in planning and forecasting processes, as the system relies on these anchors to perform calculations and generate accurate results.
  Cause:
  The error typically arises due to one or more of the following reasons:
  
  Data Inconsistencies: Missing or incomplete data in the time series can lead to a lack of anchors.
  Configuration Issues: Incorrect configuration settings in the SNP or planning area can result in missing anchors.
  Master Data Issues: Problems with master data, such as missing or incorrect product or location data, can affect the generation of time series anchors.
  Time Series Settings: The settings for time series in the planning area may not be correctly defined, leading to gaps in the data.
  
  Solution:
  To resolve this error, you can take the following steps:
  
  
  Check Time Series Data:
  
  Use transaction /SAPAPO/TS to analyze the time series data for the relevant products and locations.
  Identify any missing data points or gaps in the time series.
  
  
  
  Review Configuration:
  
  Ensure that the SNP planning area is correctly configured. Check the settings for time series and ensure that all necessary parameters are set up correctly.
  Verify that the planning version is active and correctly configured.
  
  
  
  Master Data Validation:
  
  Check the master data for products and locations to ensure that all necessary information is complete and accurate.
  Use transaction /SAPAPO/MAT1 to check the product master data and ensure that all relevant attributes are filled.
  
  
  
  Rebuild Time Series:
  
  If necessary, you can rebuild the time series data. This can be done using the transaction /SAPAPO/TS to regenerate the time series for the affected products.
  
  
  
  Run Planning Runs:
  
  After addressing the issues, run the planning runs again to see if the error persists. This can help in regenerating the anchors.
  
  
  
  Monitor and Analyze:
  
  Use transaction /SAPAPO/CCMS to monitor the system and analyze any further issues that may arise.
  
  
  
  Related Information:
  
  SAP Notes: Check for any relevant SAP Notes that may provide additional guidance or patches related to this error.
  Documentation: Refer to the SAP APO documentation for detailed information on time series management and configuration.
  Support: If the issue persists after following the above steps, consider reaching out to SAP support for further assistance.
  
  By following these steps, you should be able to identify and resolve the issue related to the missing SNP time series anchors in your SAP APO system.