How To Fix OIUCA119 - No termination points found for measurement point &.

SAP Error Message - Details

• Message type: E = Error

• Message class: OIUCA - E&P Contract Alloaction

• Message number: 119

• Message text: No termination points found for measurement point &.

Self-Explanatory Message

Since SAP believes that this specific error message is 'self-explanatory,' no more information has been given.The majority of messages in the SAP system have a message text, however this is frequently insufficient to comprehend or resolve the problem.

To make things easier, more detailed information is frequently added to describe the issue, how to fix it, and the necessary steps or configuration modifications.

Unfortunately, there isn't any extra information in this error notice.

What else can you do?

First, use our AnswerBot below to get a possible cause and solution (requires a premium subscription).

Also, review the in-depth Common Questions & Answers listed below; you could discover a solution there or be able to connect with others who have faced similar challenges.

You can also try searching the SAP support portal (support.sap.com) but you need a special user ID to access it. It is possible that an SAP support note exists that provides additional details about the mistake or even steps for fixing it.

Smart SAP Assistant

• What is the cause and solution for SAP error message OIUCA119 - No termination points found for measurement point &. ?

  The SAP error message OIUCA119, which states "No termination points found for measurement point &," typically occurs in the context of SAP's Oil and Gas (OIL) module, particularly when dealing with measurement points and their associated termination points.
  Cause:
  This error usually arises due to one of the following reasons:
  
  
  Missing Configuration: The measurement point may not be properly configured in the system. This includes not having any associated termination points defined for the measurement point.
  
  
  Data Inconsistency: There may be inconsistencies in the data, such as missing entries in the relevant tables that link measurement points to their termination points.
  
  
  Incorrect Measurement Point: The measurement point being referenced may not exist or may have been deleted or deactivated.
  
  
  Authorization Issues: Sometimes, the user may not have the necessary authorizations to view or access the termination points associated with the measurement point.
  
  
  Solution:
  To resolve the OIUCA119 error, you can take the following steps:
  
  
  Check Measurement Point Configuration:
  
  Navigate to the configuration settings for measurement points in the SAP system.
  Ensure that the measurement point in question is correctly set up and has associated termination points.
  
  
  
  Verify Termination Points:
  
  Use transaction codes like OIU1 or OIU2 to check the details of the measurement point and see if termination points are defined.
  If termination points are missing, you may need to create or link them appropriately.
  
  
  
  Data Consistency Check:
  
  Run consistency checks on the relevant tables to ensure that all necessary data is present and correctly linked.
  You may need to consult with your SAP Basis or technical team to perform deeper data integrity checks.
  
  
  
  User Authorizations:
  
  Ensure that the user encountering the error has the necessary authorizations to access the measurement point and its associated termination points.
  If needed, consult with your security team to review and adjust user roles and permissions.
  
  
  
  Consult Documentation:
  
  Refer to SAP documentation or help resources specific to the Oil and Gas module for additional guidance on measurement points and termination points.
  
  
  
  Contact SAP Support:
  
  If the issue persists after checking the above points, consider reaching out to SAP support for further assistance, especially if this is a recurring issue.
  
  
  
  Related Information:
  
  Transaction Codes: Familiarize yourself with relevant transaction codes such as OIU1 (Create Measurement Point), OIU2 (Change Measurement Point), and OIU3 (Display Measurement Point).
  SAP Notes: Check for any SAP Notes related to this error message, as they may provide specific patches or updates that address known issues.
  User Forums: Engage with SAP community forums or user groups where similar issues may have been discussed, and solutions shared.
  
  By following these steps, you should be able to identify the root cause of the OIUCA119 error and implement the necessary solutions to resolve it.