How To Fix LTR2_CM_CHECK_FLT2035 - Initial filling rule &1 not in content module repository

SAP Error Message - Details

• Message type: E = Error

• Message class: LTR2_CM_CHECK_FLT2 - LTR2 Checks on Filter2of Content Module

• Message number: 035

• Message text: Initial filling rule &1 not in content module repository

Self-Explanatory Message

Since SAP believes that this specific error message is 'self-explanatory,' no more information has been given.The majority of messages in the SAP system have a message text, however this is frequently insufficient to comprehend or resolve the problem.

To make things easier, more detailed information is frequently added to describe the issue, how to fix it, and the necessary steps or configuration modifications.

Unfortunately, there isn't any extra information in this error notice.

What else can you do?

First, use our AnswerBot below to get a possible cause and solution (requires a premium subscription).

Also, review the in-depth Common Questions & Answers listed below; you could discover a solution there or be able to connect with others who have faced similar challenges.

You can also try searching the SAP support portal (support.sap.com) but you need a special user ID to access it. It is possible that an SAP support note exists that provides additional details about the mistake or even steps for fixing it.

Smart SAP Assistant

• What is the cause and solution for SAP error message LTR2_CM_CHECK_FLT2035 - Initial filling rule &1 not in content module repository ?

  The SAP error message LTR2_CM_CHECK_FLT2035 indicates that there is an issue with the initial filling rule specified in the content module repository. This error typically arises in the context of SAP Landscape Transformation (SLT) or Data Replication scenarios where initial data loads are being configured.
  Cause:
  The error message suggests that the initial filling rule (which is a specific configuration or setting that defines how data should be initially loaded) is not found in the content module repository. This can happen due to several reasons:
  
  Missing Configuration: The initial filling rule may not have been created or activated in the system.
  Incorrect Naming: There might be a typo or mismatch in the name of the initial filling rule being referenced.
  Transport Issues: If the configuration was transported from another system, it may not have been transported correctly.
  Repository Issues: The content module repository may not be properly updated or may have inconsistencies.
  
  Solution:
  To resolve the error, you can follow these steps:
  
  
  Check Initial Filling Rule:
  
  Verify that the initial filling rule exists in the content module repository. You can do this by navigating to the relevant configuration area in SLT or the Data Replication settings.
  Ensure that the rule is correctly defined and activated.
  
  
  
  Correct Naming:
  
  Double-check the name of the initial filling rule in your configuration. Ensure that it matches exactly with what is defined in the content module repository.
  
  
  
  Transport Check:
  
  If the configuration was transported from another system, ensure that all necessary objects were included in the transport request and that the transport was successful.
  
  
  
  Repository Update:
  
  If you suspect that the content module repository is not up to date, you may need to refresh or reinitialize it. This can sometimes be done through specific transaction codes or by reloading the content.
  
  
  
  Consult Documentation:
  
  Refer to SAP documentation or notes related to SLT and initial filling rules for any specific guidance or updates that may address this issue.
  
  
  
  SAP Support:
  
  If the issue persists after checking the above points, consider reaching out to SAP Support for further assistance. They may provide additional insights or patches if this is a known issue.
  
  
  
  Related Information:
  
  Transaction Codes: Familiarize yourself with relevant transaction codes such as LTRC (for SLT configuration) and LTR2 (for content module management).
  SAP Notes: Search for SAP Notes related to SLT and initial filling rules, as they may contain specific fixes or workarounds for known issues.
  Community Forums: Engage with SAP community forums or user groups where similar issues may have been discussed, and solutions shared.
  
  By following these steps, you should be able to identify and resolve the cause of the error message LTR2_CM_CHECK_FLT2035.