How To Fix /ISDFPS/MM107 - MRP area &2 of force element &3 already contains storage location &1

SAP Error Message - Details

• Message type: E = Error

• Message class: /ISDFPS/MM -

• Message number: 107

• Message text: MRP area &2 of force element &3 already contains storage location &1

Self-Explanatory Message

Since SAP believes that this specific error message is 'self-explanatory,' no more information has been given.The majority of messages in the SAP system have a message text, however this is frequently insufficient to comprehend or resolve the problem.

To make things easier, more detailed information is frequently added to describe the issue, how to fix it, and the necessary steps or configuration modifications.

Unfortunately, there isn't any extra information in this error notice.

What else can you do?

First, use our AnswerBot below to get a possible cause and solution (requires a premium subscription).

Also, review the in-depth Common Questions & Answers listed below; you could discover a solution there or be able to connect with others who have faced similar challenges.

You can also try searching the SAP support portal (support.sap.com) but you need a special user ID to access it. It is possible that an SAP support note exists that provides additional details about the mistake or even steps for fixing it.

Smart SAP Assistant

• What is the cause and solution for SAP error message /ISDFPS/MM107 - MRP area &2 of force element &3 already contains storage location &1 ?

  The SAP error message /ISDFPS/MM107 indicates that there is an issue related to the configuration of MRP (Material Requirements Planning) areas and storage locations in the system. Specifically, the message states that the MRP area for a particular force element already contains the specified storage location, which is causing a conflict.
  Cause:
  This error typically arises due to one of the following reasons:
  
  Duplicate Entries: The storage location is already assigned to the MRP area for the specified force element, leading to a conflict when trying to add it again.
  Configuration Issues: There may be incorrect or incomplete configuration in the MRP area settings, causing the system to misinterpret the storage location assignments.
  Data Consistency Issues: There might be inconsistencies in the master data or transactional data related to the MRP area and storage locations.
  
  Solution:
  To resolve this error, you can take the following steps:
  
  
  Check Existing Assignments:
  
  Navigate to the MRP area configuration in SAP and check the existing assignments for the specified force element and storage location.
  Ensure that the storage location is not already assigned to the MRP area.
  
  
  
  Remove Duplicate Entries:
  
  If you find that the storage location is indeed already assigned, you may need to remove the duplicate entry or adjust the configuration to avoid conflicts.
  
  
  
  Review MRP Area Configuration:
  
  Go to the configuration settings for MRP areas and verify that all settings are correct and complete.
  Ensure that the storage locations and force elements are properly defined and do not overlap inappropriately.
  
  
  
  Data Consistency Check:
  
  Perform a data consistency check to identify any discrepancies in the master data related to the MRP area and storage locations.
  Use transaction codes like MM02 to modify material master data or OMD1 to check MRP area settings.
  
  
  
  Consult Documentation:
  
  Refer to SAP documentation or help resources for specific guidance on MRP area configuration and troubleshooting.
  
  
  
  Contact SAP Support:
  
  If the issue persists after checking the above points, consider reaching out to SAP support for further assistance.
  
  
  
  Related Information:
  
  MRP Areas: MRP areas are used in SAP to manage inventory and planning at a more granular level than just the plant level. They allow for specific planning and control of materials in different storage locations.
  Force Elements: These are used in the context of MRP to define specific planning parameters and requirements for materials.
  Storage Locations: These are physical locations within a plant where materials are stored. Each storage location can have its own inventory and planning characteristics.
  
  By following these steps, you should be able to identify and resolve the issue causing the error message /ISDFPS/MM107.