How To Fix HUGENERAL046 - Quantity cannot be rounded off for unit of measure &1

SAP Error Message - Details

• Message type: E = Error

• Message class: HUGENERAL - Handling Units - Packing

• Message number: 046

• Message text: Quantity cannot be rounded off for unit of measure &1

Self-Explanatory Message

Since SAP believes that this specific error message is 'self-explanatory,' no more information has been given.The majority of messages in the SAP system have a message text, however this is frequently insufficient to comprehend or resolve the problem.

To make things easier, more detailed information is frequently added to describe the issue, how to fix it, and the necessary steps or configuration modifications.

Unfortunately, there isn't any extra information in this error notice.

What else can you do?

First, use our AnswerBot below to get a possible cause and solution (requires a premium subscription).

Also, review the in-depth Common Questions & Answers listed below; you could discover a solution there or be able to connect with others who have faced similar challenges.

You can also try searching the SAP support portal (support.sap.com) but you need a special user ID to access it. It is possible that an SAP support note exists that provides additional details about the mistake or even steps for fixing it.

Smart SAP Assistant

• What is the cause and solution for SAP error message HUGENERAL046 - Quantity cannot be rounded off for unit of measure &1 ?

  The SAP error message HUGENERAL046, which states "Quantity cannot be rounded off for unit of measure &1," typically occurs when there is an issue with the quantity being processed in relation to the unit of measure (UoM) defined for a material or product. This error can arise in various scenarios, such as during goods movements, inventory management, or when creating purchase orders.
  Cause:
  
  
  Incompatible UoM: The quantity being entered may not be compatible with the defined unit of measure for the material. For example, if the UoM is set to a specific decimal precision, and the quantity being entered has more decimal places than allowed, this error can occur.
  
  
  Rounding Rules: The rounding rules defined for the material or the unit of measure may not allow the quantity to be rounded to a permissible value. This can happen if the quantity does not conform to the expected increments or if the rounding settings are not properly configured.
  
  
  Configuration Issues: There may be issues in the configuration of the material master data, particularly in the units of measure section, where the base unit of measure and alternative units of measure are defined.
  
  
  Solution:
  
  
  Check Quantity: Verify the quantity being entered and ensure it adheres to the allowed decimal places for the unit of measure. Adjust the quantity if necessary.
  
  
  Review UoM Settings: Go to the material master data (transaction code MM03) and check the unit of measure settings. Ensure that the base unit of measure and any alternative units of measure are correctly defined and that their conversion factors are accurate.
  
  
  Adjust Rounding Rules: If applicable, review the rounding rules for the unit of measure in the configuration settings. You may need to adjust these settings to allow for the quantity to be rounded appropriately.
  
  
  Consult Documentation: Refer to SAP documentation or help resources for specific guidance on handling units of measure and rounding issues.
  
  
  Test with Different Quantities: If possible, test the transaction with different quantities to identify if the issue is specific to certain values.
  
  
  Contact SAP Support: If the issue persists after checking the above points, consider reaching out to SAP support for further assistance, especially if it appears to be a configuration issue.
  
  
  Related Information:
  
  Transaction Codes: MM03 (Display Material), MM02 (Change Material), and MM01 (Create Material) can be used to check and modify material master data.
  Unit of Measure Configuration: The configuration for units of measure can be found in the SAP IMG under Logistics General > Material Master > Basic Settings > Define Units of Measure.
  Rounding Settings: Rounding settings can be configured in the same IMG area, where you can define how quantities should be rounded based on the unit of measure.
  
  By following these steps, you should be able to identify and resolve the issue related to the HUGENERAL046 error message in SAP.