Do you have any question about this error?
Message type: E = Error
Message class: HRPBS00CA - HCM: Calculation Modules
Message number: 310
Message text: Class &1 is of an incorrect type. Please check the Customizing.
Class &V1& does not exist or has been incorrectly categorized. ,,
The system issues an error message and will not allow you to continue with this transaction until the error is resolved.
Ensure that class &V1& is inherited from standard class
CL_HRPBSCA_NOTIF_FORM_SERVICES. Use transaction SM30 under view Sicht
V_T7PBSCA6A to check if your class &V1& has been entered as a service
class for the relevant interface and data class &V2&.
Error message extract from SAP system. Copyright SAP SE.
The SAP error message HRPBS00CA310 indicates that there is an issue with the classification of a specific object in the system. The message states that "Class &1 is of an incorrect type," which suggests that the system is expecting a different type of classification than what has been provided.
Cause:
- Incorrect Class Type: The class specified in the error message does not match the expected type for the operation being performed. This could be due to a misconfiguration in the Customizing settings.
- Customizing Settings: The Customizing settings for the classification system may not be correctly defined, leading to the system not recognizing the class type.
- Data Entry Error: There may be a mistake in the data entry where an incorrect class was assigned to an object.
Solution:
Check Customizing Settings:
- Navigate to the Customizing settings in SAP (Transaction SPRO).
- Go to the relevant section for the classification system and verify that the class type is correctly defined.
- Ensure that the class type corresponds to the object type you are working with.
Verify Class Assignment:
- Check the specific object that is causing the error and verify that the correct class is assigned.
- If necessary, reassign the correct class that matches the expected type.
Review Documentation:
- Consult the SAP documentation or help files related to the classification system to understand the expected class types for your specific scenario.
Testing:
- After making changes, test the process again to see if the error persists.
Consult with SAP Support:
- If the issue cannot be resolved through the above steps, consider reaching out to SAP support for further assistance.
Related Information:
CL02
(Change Class) and CL03
(Display Class) to manage class definitions.By following these steps, you should be able to identify the cause of the error and implement a solution to resolve it.
Get instant SAP help. Start your 7-day free trial now.
Feature | Free Access | Free Trial |
---|---|---|
Basic SAP error explanation | ![]() |
![]() |
Step-by-Step Usage Guide | ![]() |
![]() |
Interactive SAP Coach Assistance | ![]() |
![]() |
AI Troubleshooting for T-Code Errors | ![]() |
![]() |
HRPBS00CA309 No interface for form &1 can be found.
What causes this issue? No corresponding interface was found for adobe form &am...
HRPBS00CA305 Missing end symbol placeholder (form data class &1, component &2)
What causes this issue? You have assigned a placeholder to component &V2&am...
HRPBS00GNP000 Not a valid GNP Code &
What causes this issue? Not a valid GNP Code.System Response The system issues...
HRPBS00GNP001 Queue name cannot be empty.
Self-Explanatory Message Since SAP believes that this specific error message is ...
SAP messages fall into 3 different categories: Error messages
(message type = E), Warnings (W) or Informational (I) messages.
An error message will prevent you from continuing your work - it is a hard stop and you need to fix the error before you can proceed. A warning message will stop your work, however, you can then bypass the warning by pressing the Enter key on your keyboard. That said, it is still good practice to investigate the cause of the warning message and address it. An information message will not stop your work and is truly just for informational purposes.
Click on this link to search all SAP messages.