How To Fix /DSD/SV310 - Unit of measurement &1 for material &2 not maintained.

SAP Error Message - Details

• Message type: E = Error

• Message class: /DSD/SV -

• Message number: 310

• Message text: Unit of measurement &1 for material &2 not maintained.

Self-Explanatory Message

Since SAP believes that this specific error message is 'self-explanatory,' no more information has been given.The majority of messages in the SAP system have a message text, however this is frequently insufficient to comprehend or resolve the problem.

To make things easier, more detailed information is frequently added to describe the issue, how to fix it, and the necessary steps or configuration modifications.

Unfortunately, there isn't any extra information in this error notice.

What else can you do?

First, use our AnswerBot below to get a possible cause and solution (requires a premium subscription).

Also, review the in-depth Common Questions & Answers listed below; you could discover a solution there or be able to connect with others who have faced similar challenges.

You can also try searching the SAP support portal (support.sap.com) but you need a special user ID to access it. It is possible that an SAP support note exists that provides additional details about the mistake or even steps for fixing it.

Smart SAP Assistant

• What is the cause and solution for SAP error message /DSD/SV310 - Unit of measurement &1 for material &2 not maintained. ?

  The SAP error message /DSD/SV310 Unit of measurement &1 for material &2 not maintained typically occurs in the context of the SAP Direct Store Delivery (DSD) module when there is an issue with the unit of measurement (UoM) for a specific material. Here’s a breakdown of the cause, potential solutions, and related information:
  Cause:
  
  Missing UoM Configuration: The specified unit of measurement (UoM) for the material in question is not maintained in the system. This could happen if the material was created without defining a UoM or if the UoM was deleted or not properly configured.
  Material Master Data Issues: The material master data may not have been fully maintained, leading to missing information regarding the UoM.
  Incorrect UoM Usage: The UoM being referenced may not be valid for the material type or may not be set up correctly in the system.
  
  Solution:
  
  
  Check Material Master Data:
  
  Go to the Material Master (transaction code MM03).
  Enter the material number and check the Basic Data view and Sales Organization view to ensure that the UoM is maintained correctly.
  If the UoM is missing, you can add it using transaction code MM02 (Change Material).
  
  
  
  Maintain UoM in the Material Master:
  
  If the UoM is not maintained, you can add it by navigating to the relevant views in the Material Master and entering the appropriate UoM.
  Ensure that the UoM is valid and corresponds to the material type.
  
  
  
  Check UoM Configuration:
  
  Use transaction code CUNI to check the unit of measure settings in the system.
  Ensure that the UoM is defined in the system and is linked to the material.
  
  
  
  Review UoM Conversion:
  
  If the material uses multiple UoMs, ensure that the conversion factors are correctly defined in the material master.
  
  
  
  Consult with SAP Support:
  
  If the issue persists after checking the above points, consider reaching out to your SAP support team or consulting SAP Notes for any known issues related to this error.
  
  
  
  Related Information:
  
  Transaction Codes:
  
  MM03: Display Material Master
  MM02: Change Material Master
  CUNI: Maintain Units of Measure
  
  
  SAP Documentation: Refer to SAP Help documentation for detailed information on material master data and unit of measurement configuration.
  SAP Notes: Check for any relevant SAP Notes that may address specific issues or bugs related to this error message.
  
  By following these steps, you should be able to resolve the error message and ensure that the unit of measurement for the specified material is properly maintained in the SAP system.