How To Fix CM_EHFND_API_CCI086 - &1: Unit of measurement &2 is not found.

SAP Error Message - Details

• Message type: E = Error

• Message class: CM_EHFND_API_CCI - Messages for chemical compliance view API

• Message number: 086

• Message text: &1: Unit of measurement &2 is not found.

What causes this issue?

The application &V2& of the object &V3& with &V1& number was not found.

System Response

The system does not change or delete the application.
The system stops processing of the object &V3& with &V1& number.

How to fix this error?

Ensure that the application &V2& exists in the system.
Try to transfer data of object &V3& with &V1& number again.

Procedure for System Administrators

The system issues an error message and will not allow you to continue with this transaction until the error is resolved.

Error message extract from SAP system. Copyright SAP SE.

Smart SAP Assistant

• What is the cause and solution for SAP error message CM_EHFND_API_CCI086 - &1: Unit of measurement &2 is not found. ?

  The SAP error message CM_EHFND_API_CCI086 indicates that a specific unit of measurement (UoM) is not found in the system. This error typically occurs when trying to process data related to materials, products, or services that require a specific unit of measurement that has not been defined or is incorrectly specified in the system.
  Cause:
  
  Missing Unit of Measurement: The specified unit of measurement (UoM) does not exist in the SAP system.
  Incorrect UoM Code: The UoM code being used may be misspelled or incorrectly formatted.
  Configuration Issues: The unit of measurement may not be properly configured in the relevant SAP modules (e.g., Material Management, Sales and Distribution).
  Data Migration Issues: If data has been migrated from another system, the UoM may not have been included in the migration process.
  
  Solution:
  
  
  Check UoM Configuration:
  
  Go to the transaction code CUNI (Unit of Measure) in SAP.
  Verify if the UoM in question exists. If it does not, you will need to create it.
  If it exists, ensure that it is active and correctly configured.
  
  
  
  Create Missing UoM:
  
  If the UoM is missing, you can create it by using the following steps:
  
  Navigate to CUNI.
  Click on "New Entries" and enter the required details for the new unit of measurement.
  Save your changes.
  
  
  
  
  
  Check for Typos:
  
  Review the code or identifier for the UoM in your transaction or program to ensure there are no typographical errors.
  
  
  
  Review Data Migration:
  
  If this error occurred after a data migration, check the migration logs to ensure that all necessary UoMs were included in the migration process.
  
  
  
  Consult Documentation:
  
  Refer to SAP documentation or help resources for additional guidance on UoM configuration and management.
  
  
  
  Contact SAP Support:
  
  If the issue persists after checking the above points, consider reaching out to SAP support for further assistance.
  
  
  
  Related Information:
  
  Unit of Measurement (UoM): In SAP, UoMs are used to define how quantities of materials or products are measured (e.g., pieces, kilograms, liters).
  Transaction Codes: Familiarize yourself with relevant transaction codes such as:
  
  CUNI: For managing units of measurement.
  MM01: For creating materials, where you can specify UoMs.
  MM02: For changing material data, including UoMs.
  
  
  SAP Notes: Check SAP Notes for any known issues or patches related to this error message.
  
  By following these steps, you should be able to resolve the error message CM_EHFND_API_CCI086 and ensure that the required unit of measurement is available in your SAP system.