How To Fix APB_FPM_CONF084 - Sum of all widths is &1 and should be equal to 100

SAP Error Message - Details

• Message type: E = Error

• Message class: APB_FPM_CONF -

• Message number: 084

• Message text: Sum of all widths is &1 and should be equal to 100

Self-Explanatory Message

Since SAP believes that this specific error message is 'self-explanatory,' no more information has been given.The majority of messages in the SAP system have a message text, however this is frequently insufficient to comprehend or resolve the problem.

To make things easier, more detailed information is frequently added to describe the issue, how to fix it, and the necessary steps or configuration modifications.

Unfortunately, there isn't any extra information in this error notice.

What else can you do?

First, use our AnswerBot below to get a possible cause and solution (requires a premium subscription).

Also, review the in-depth Common Questions & Answers listed below; you could discover a solution there or be able to connect with others who have faced similar challenges.

You can also try searching the SAP support portal (support.sap.com) but you need a special user ID to access it. It is possible that an SAP support note exists that provides additional details about the mistake or even steps for fixing it.

Smart SAP Assistant

• What is the cause and solution for SAP error message APB_FPM_CONF084 - Sum of all widths is &1 and should be equal to 100 ?

  The SAP error message APB_FPM_CONF084 indicates that there is a configuration issue in the Floorplan Manager (FPM) application. Specifically, it points out that the sum of the widths defined for the UI elements in a certain layout does not equal 100%. This is a common requirement in FPM configurations, as the total width of all components in a layout must equal 100% to ensure proper rendering and alignment.
  Cause:
  The error occurs when the widths of the UI elements (like columns, sections, or other components) defined in the FPM configuration do not add up to 100%. This can happen due to:
  
  Incorrect manual configuration of widths.
  Missing or misconfigured components.
  Changes in the layout that were not properly accounted for in the width settings.
  
  Solution:
  To resolve this error, follow these steps:
  
  
  Check the Configuration:
  
  Open the FPM configuration for the application where the error occurs.
  Navigate to the layout settings where the widths are defined.
  
  
  
  Verify Widths:
  
  Review the widths assigned to each UI element. Ensure that the sum of all widths equals 100%.
  If you have defined widths in percentages, make sure they are correctly calculated. For example, if you have three columns with widths of 30%, 40%, and 30%, this would cause the error since they sum to 100% but if one of them is set to 35%, it would sum to 105%.
  
  
  
  Adjust Widths:
  
  Modify the widths of the components as necessary to ensure they total 100%. You may need to increase or decrease the width of certain elements or redistribute the widths among them.
  
  
  
  Test the Configuration:
  
  After making adjustments, save the configuration and test the application to ensure that the error is resolved and that the layout displays correctly.
  
  
  
  Documentation:
  
  If you are unsure about the correct widths, refer to the SAP documentation or guidelines for the specific FPM application you are working with. This can provide insights into standard practices for layout configurations.
  
  
  
  Related Information:
  
  FPM Documentation: SAP provides extensive documentation on Floorplan Manager configurations, which can be helpful in understanding how to set up layouts correctly.
  SAP Community: Engaging with the SAP Community can provide additional insights and solutions from other users who may have encountered similar issues.
  SAP Notes: Check for any relevant SAP Notes that might address known issues or provide patches related to FPM configurations.
  
  By following these steps, you should be able to resolve the APB_FPM_CONF084 error and ensure that your FPM application is configured correctly.