How To Fix ADS2KIPUPL_AL114 - If SPQ is given, then Start PBQ/End PBQ must be in multiples of SPQ

SAP Error Message - Details

• Message type: E = Error

• Message class: ADS2KIPUPL_AL - SPEC2000 Initial Provisioning: Upload Appl. Layer Messages

• Message number: 114

• Message text: If SPQ is given, then Start PBQ/End PBQ must be in multiples of SPQ

Self-Explanatory Message

Since SAP believes that this specific error message is 'self-explanatory,' no more information has been given.The majority of messages in the SAP system have a message text, however this is frequently insufficient to comprehend or resolve the problem.

To make things easier, more detailed information is frequently added to describe the issue, how to fix it, and the necessary steps or configuration modifications.

Unfortunately, there isn't any extra information in this error notice.

What else can you do?

First, use our AnswerBot below to get a possible cause and solution (requires a premium subscription).

Also, review the in-depth Common Questions & Answers listed below; you could discover a solution there or be able to connect with others who have faced similar challenges.

You can also try searching the SAP support portal (support.sap.com) but you need a special user ID to access it. It is possible that an SAP support note exists that provides additional details about the mistake or even steps for fixing it.

Smart SAP Assistant

• What is the cause and solution for SAP error message ADS2KIPUPL_AL114 - If SPQ is given, then Start PBQ/End PBQ must be in multiples of SPQ ?

  The SAP error message ADS2KIPUPL_AL114 indicates that there is an issue with the configuration of the scheduling parameters for a process in SAP, specifically related to the Start PBQ (Process Block Quantity) and End PBQ settings. The error message states that if a specific SPQ (Standard Process Quantity) is provided, then both the Start PBQ and End PBQ must be multiples of the SPQ.
  Cause:
  This error typically arises in scenarios where:
  
  The Start PBQ and End PBQ values are not aligned with the SPQ. For example, if the SPQ is set to 10, then both Start PBQ and End PBQ should be values like 10, 20, 30, etc.
  There may be a misconfiguration in the production planning or scheduling settings in the SAP system.
  The values entered for Start PBQ and End PBQ do not adhere to the expected multiples of the SPQ, leading to this validation error.
  
  Solution:
  To resolve this error, you can take the following steps:
  
  
  Check SPQ Configuration: Verify the SPQ value set in the system. Ensure that it is correctly defined and reflects the intended process quantity.
  
  
  Adjust Start PBQ and End PBQ:
  
  Go to the relevant transaction or configuration screen where you can set the Start PBQ and End PBQ.
  Ensure that both values are multiples of the SPQ. For example, if SPQ is 10, valid values for Start PBQ and End PBQ could be 10, 20, 30, etc.
  
  
  
  Review Production Orders: If this error occurs during the processing of production orders, check the order details to ensure that the quantities specified are correct and conform to the SPQ.
  
  
  Consult Documentation: Refer to SAP documentation or help resources for specific guidelines on setting up PBQ and SPQ values.
  
  
  Testing: After making the necessary adjustments, test the configuration to ensure that the error no longer occurs.
  
  
  Related Information:
  
  Transaction Codes: Depending on your SAP version, you may use transaction codes like CO01 (Create Production Order) or CO02 (Change Production Order) to check and modify the relevant settings.
  SAP Notes: Check for any SAP Notes related to this error message for additional insights or patches that may address the issue.
  User Roles: Ensure that you have the necessary permissions to make changes to production planning settings in SAP.
  
  If the issue persists after following these steps, it may be beneficial to consult with your SAP support team or a technical consultant who can provide further assistance.