How To Fix UCM0060 - Totals records do not contain characteristic &2 with the role &3

SAP Error Message - Details

• Message type: E = Error

• Message class: UCM0 - Messages for Data Basis, Cons Area, ...

• Message number: 060

• Message text: Totals records do not contain characteristic &2 with the role &3

What causes this issue?

In <DS:GLOS.3C14A7065A82D511B1250008C784EFB1>data basis</> &V1&, the
characteristic with the technical name &V2& has the role &V3&.
Characteristics with this role should be part of the data stream for
data records. However, this is not the case here.

System Response

Executing consolidation functions in the present status can be
restricted.

How to fix this error?

Check the definition of data basis &V1&.
A possible cause for the error is that a characteristic was swapped in
the InfoCube. In this case, proceed as follows:
Include the new characteristic in the data basis.
Assign the appropriate role to the characteristic.
Save your settings.
Start the workbench again.

Procedure for System Administrators

The system issues an error message and will not allow you to continue with this transaction until the error is resolved.

Error message extract from SAP system. Copyright SAP SE.

Smart SAP Assistant

• What is the cause and solution for SAP error message UCM0060 - Totals records do not contain characteristic &2 with the role &3 ?

  The SAP error message UCM0060 indicates that there is an issue with the totals records in the context of the SAP system, specifically related to the absence of a characteristic in the totals records that is expected based on the role defined.
  Cause:
  The error message UCM0060 typically arises due to one of the following reasons:
  
  
  Missing Characteristic: The characteristic specified in the error message (denoted as &2) is not present in the totals records for the specified role (denoted as &3). This can happen if the characteristic was not included in the data model or if it was removed or not properly configured.
  
  
  Configuration Issues: There may be a misconfiguration in the data model or the settings related to the role that is being used. This could involve incorrect settings in the InfoObject or the aggregation settings.
  
  
  Data Load Issues: If the data load process did not complete successfully or if there were errors during the data extraction or transformation, it could lead to missing characteristics in the totals records.
  
  
  Solution:
  To resolve the UCM0060 error, you can take the following steps:
  
  
  Check the Data Model: Verify that the characteristic mentioned in the error message is included in the data model. Ensure that it is properly defined and activated.
  
  
  Review Role Configuration: Check the configuration of the role specified in the error message. Ensure that the role is correctly set up to include the necessary characteristics.
  
  
  Data Load Verification: Review the data load process to ensure that it completed successfully. Check for any errors or warnings in the data load logs that might indicate issues with the extraction or transformation of data.
  
  
  Reprocess Totals Records: If necessary, you may need to reprocess the totals records. This can involve running the appropriate data aggregation or update processes to ensure that the totals records are correctly populated with the required characteristics.
  
  
  Consult Documentation: Refer to SAP documentation or support notes related to the specific version of SAP you are using. There may be specific guidelines or patches available that address this error.
  
  
  Contact SAP Support: If the issue persists after trying the above steps, consider reaching out to SAP support for further assistance. They can provide more detailed insights based on your specific system configuration and data model.
  
  
  Related Information:
  
  SAP Notes: Check for any relevant SAP Notes that might address this specific error or provide additional troubleshooting steps.
  Transaction Codes: Familiarize yourself with transaction codes related to data modeling and data loading, such as RSA1 (Data Warehousing Workbench) and RSMO (Monitor Data Load).
  Community Forums: Engage with SAP community forums or user groups where similar issues may have been discussed, and solutions shared.
  
  By following these steps, you should be able to identify the root cause of the UCM0060 error and implement a solution to resolve it.